| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
|
|
| |
To support this, a core.gcrypt-id is stored by git-annex inside the git
config of a local gcrypt repository, when setting it up.
That is compared with the remote's cached gcrypt-id. When different, a
drive has been changed. git-annex then looks up the remote config for
the uuid mapped from the core.gcrypt-id, and tweaks the configuration
appropriately. When there is no known config for the uuid, it will refuse to
use the remote.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is a git-remote-gcrypt encrypted special remote. Only sending files
in to the remote works, and only for local repositories.
Most of the work so far has involved making initremote work. A particular
problem is that remote setup in this case needs to generate its own uuid,
derivied from the gcrypt-id. That required some larger changes in the code
to support.
For ssh remotes, this will probably just reuse Remote.Rsync's code, so
should be easy enough. And for downloading from a web remote, I will need
to factor out the part of Remote.Git that does that.
One particular thing that will need work is supporting hot-swapping a local
gcrypt remote. I think it needs to store the gcrypt-id in the git config of the
local remote, so that it can check it every time, and compare with the
cached annex-uuid for the remote. If there is a mismatch, it can change
both the cached annex-uuid and the gcrypt-id. That should work, and I laid
some groundwork for it by already reading the remote's config when it's
local. (Also needed for other reasons.)
This commit was sponsored by Daniel Callahan.
|
|
|
|
|
|
|
|
|
|
|
|
| |
With the initremote parameters "encryption=pubkey keyid=788A3F4C".
/!\ Adding or removing a key has NO effect on files that have already
been copied to the remote. Hence using keyid+= and keyid-= with such
remotes should be used with care, and make little sense unless the point
is to replace a (sub-)key by another. /!\
Also, a test case has been added to ensure that the cipher and file
contents are encrypted as specified by the chosen encryption scheme.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
uploads to the same glacier repository by `git annex copy`.
The checkpresent hook can return either True or, False, or fail with a message
if it cannot successfully check the remote. Currently for glacier, when
--trust-glacier is not set, it always returns False. Crucially, in the case
when a file is in glacier, this is telling git-annex it's not there, so copy
re-uploads it. This is not desirable; it breaks using glacier-cli to retreive
that file later, and it wastes money/bandwidth.
What if it instead, when the glacier inventory is missing a
file, it returns False. And when the glacier inventory has a file, unless
--trust-glacier is set, it *fails*.
The result would be:
* `git annex copy --to glacier` would only send things not listed in inventory. If a file is listed in the inventory, `copy`
would complain that --trust-glacier` is not set, and not re-upload the file.
* `git annex drop` would only trust that glacier has a file when --trust-glacier is set. Behavior unchanged.
* `git annex move --to glacier`, when the file is not listed in inventory, would send the file, and delete it locally. Behavior unchanged.
* `git annex move --to glacier`, when the file is listed in inventory, would only trust that glacier has the file when --trust-glacier is set
* `git annex copy --from glacier` / `git annex get`, when the file is located in glacier, would trust the location log, and attempt to get the file from glacier.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Most remotes have meters in their implementations of retrieveKeyFile
already. Simply hooking these up to the transfer log makes that information
available. Easy peasy.
This is particularly valuable information for encrypted remotes, which
otherwise bypass the assistant's polling of temp files, and so don't have
good progress bars yet.
Still some work to do here (see progressbars.mdwn changes), but this
is entirely an improvement from the lack of progress bars for encrypted
downloads.
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There was confusion in different parts of the progress bar code about
whether an update contained the total number of bytes transferred, or the
number of bytes transferred since the last update. One way this bug
showed up was progress bars that seemed to stick at zero for a long time.
In order to fix it comprehensively, I add a new BytesProcessed data type,
that is explicitly a total quantity of bytes, not a delta.
Note that this doesn't necessarily fix every problem with progress bars.
Particularly, buffering can now cause progress bars to seem to run ahead
of transfers, reaching 100% when data is still being uploaded.
|
| |
|
|
|
|
|
| |
Added a function to insert a new cost into a list, which could be used to
asjust costs after a drag and drop.
|
| |
|
|
|
|
| |
the transfer, which can happen in direct mode.
|
| |
|
|
|
|
|
| |
Still a couple of places that use git config ad-hoc, but this is most of it
done.
|
| |
|
|
|
|
| |
currently-supported AWS regions.
|
| |
|
| |
|
|
|
|
| |
one-click enabling of the repository.
|
|
|
|
| |
The meter code does that too.
|
| |
|
| |
|
|
|
|
|
|
| |
Higher than any other remote, this is mostly due to the long retrieval
time, so it'd make sense to get a file from nearly any other remote.
(Unless it's behind a very slow connection.)
|
| |
|
|
|