| Commit message (Collapse) | Author | Age |
|---|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| | |
This reverts a5031031f0d596b2381a785925beb574d90a862e and properly fixes
the issue discussed there.
This makes git-annex behave much nicer in direct mode.
|
| | | |
|
| |/ |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Sometimes it seems that git-cat-file --batch stops getting info for
files in the current repo, when ":file" is fed to it. I have not reproduced
this at the command line, but only when using git annex whereis and git
annex move inside a direct mode repo. Those failed, because cat-file
returned "file missing". OTOH, git annex find works fine, despite passing
the same file to cat-file. It seems that the failing commands first asked
cat-file to show a file on the git-annex branch. Perhaps it got "stuck" on
that branch? But I cannot repoduce it running cat-file by hand. Most
strange. HEAD is a workaround for this extreme weirdness, since I spent a
good 2 hours struggling with it already.
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The expensive scan uses lookupFile, but in direct mode, that doesn't work
for files that are present. So the scan was not finding things that are
present that need to be uploaded. (It did find things not present that
needed to be downloaded.)
Now lookupFile also works in direct mode. Note that it still prefers
symlinks on disk to info committed to git, in direct mode. This is
necessary to make things like Assistant.Threads.Watcher.onAddSymlink
work correctly, when given a new symlink not yet checked into git (or
replacing a file checked into git).
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
When a file is changed in direct mode, the old content is probably lost
(at least from the local repo), and bookeeping needs to be updated to
reflect this.
Also, synthetic add events are generated at assistant startup, so
make it detect when the file has not really changed, and avoid re-adding
it.
This does add the overhead of querying the runing git cat-file for the
key that's recorded in git for the file, each time a file is added or
modified in direct mode.
|
| |\
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
Annex/CatFile.hs
Annex/Content.hs
Git/LsFiles.hs
Git/LsTree.hs
|
| | | |
|
| |/ |
|
| |
|
|
|
| |
This interface is not a good idea, because a running git cat-file --batch
does not notice when existing files in the index are changed.
|
| | |
|
| |
|
|
|
| |
Its truncation behavior is a red flag, so avoid using it in these places
where only raw ByteStrings are used, without looking at the data inside.
|
| |
|
|
| |
Crazy like a fox..
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Dealing with a race without using locking is exceedingly difficult and tricky.
Fully tested, I hope.
There are three places left where the branch can be updated, that are not
covered by the race recovery code. Let's prove they're all immune to the
race:
1. tryFastForwardTo checks to see if a fast-forward can be done,
and then does git-update-ref on the branch to fast-forward it.
If a push comes in before the check, then either no fast-forward
will be done (ok), or the push set the branch to a ref that can
still be fast-forwarded (also ok)
If a push comes in after the check, the git-update-ref will
undo the ref change made by the push. It's as if the push did not come
in, and the next git-push will see this, and try to re-do it.
(acceptable)
2. When creating the branch for the very first time, an empty index
is created, and a commit of it made to the branch. The commit's ref
is recorded as the current state of the index. If a push came in
during that, it will be noticed the next time a commit is made to the
branch, since the branch will have changed. (ok)
3. Creating the branch from an existing remote branch involves making
the branch, and then getting its ref, and recording that the index
reflects that ref.
If a push creates the branch first, git-branch will fail (ok).
If the branch is created and a racing push is then able to change it
(highly unlikely!) we're still ok, because it first records the ref into
the index.lck, and then updating the index. The race can cause the
index.lck to have the old branch ref, while the index has the newly pushed
branch merged into it, but that only results in an unnecessary update of
the index file later on.
|
| |
|
|
|
|
|
|
|
|
|
| |
In git, a Ref can be a Sha, or a Branch, or a Tag. I added type aliases for
those. Note that this does not prevent mixing up of eg, refs and branches
at the type level. Since git really doesn't care, except rare cases like
git update-ref, or git tag -d, that seems ok for now.
There's also a tree-ish, but let's just use Ref for it. A given Sha or Ref
may or may not be a tree-ish, depending on the object type, so there seems
no point in trying to represent it at the type level.
|
| | |
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Many functions took the repo as their first parameter. Changing it
consistently to be the last parameter allows doing some useful things with
currying, that reduce boilerplate.
In particular, g <- gitRepo is almost never needed now, instead
use inRepo to run an IO action in the repo, and fromRepo to get
a value from the repo.
This also provides more opportunities to use monadic and applicative
combinators.
|
| | |
|
| |
|
Joey Hess
Joey Hess