2 files changed, 88 insertions, 0 deletions
diff --git a/doc/design/assistant/syncing/comment_2_eb992b5b2c7a5ce23443e2a6007e5ff9._comment b/doc/design/assistant/syncing/comment_2_eb992b5b2c7a5ce23443e2a6007e5ff9._comment
new file mode 100644
index 000000000..a4609d7e1
--- /dev/null
+++ b/doc/design/assistant/syncing/comment_2_eb992b5b2c7a5ce23443e2a6007e5ff9._comment
@@ -0,0 +1,8 @@
+[[!comment format=mdwn
+ username="https://www.google.com/accounts/o8/id?id=AItOawnBl7cA6wLDxVNUyLIHvAyCkf8ir3alYpk"
+ nickname="Tyson"
+ subject="Bridging LANs"
+ date="2012-07-10T10:20:59Z"
+ content="""
+Why rely on the cloud when you can instead use XMPP and jingle to perform NAT traversal for you? AFAIKT, it also means that traffic won't leave your router if the two endpoints are behind the same router.
+"""]]
diff --git a/doc/design/assistant/syncing/comment_3_e1b5e8a24556de16d1cacd27ee0c1bd1._comment b/doc/design/assistant/syncing/comment_3_e1b5e8a24556de16d1cacd27ee0c1bd1._comment
new file mode 100644
index 000000000..c9118595c
--- /dev/null
+++ b/doc/design/assistant/syncing/comment_3_e1b5e8a24556de16d1cacd27ee0c1bd1._comment
@@ -0,0 +1,80 @@
+[[!comment format=mdwn
+ username="https://www.google.com/accounts/o8/id?id=AItOawkSq2FDpK2n66QRUxtqqdbyDuwgbQmUWus"
+ nickname="Jimmy"
+ subject="comment 1"
+ date="2012-07-03T08:26:43Z"
+ content="""
+On \"git syncing\" point number 9, on OSX you could potentially do this on a semi-regular basis
+
+<pre>
+system_profiler SPNetworkVolumeDataType
+Volumes:
+
+    net:
+
+      Type: autofs
+      Mount Point: /net
+      Mounted From: map -hosts
+      Automounted: Yes
+
+    home:
+
+      Type: autofs
+      Mount Point: /home
+      Mounted From: map auto_home
+      Automounted: Yes
+</pre>
+
+and
+
+<pre>
+x00:~ jtang$ system_profiler SPUSBDataType
+USB:
+
+    USB High-Speed Bus:
+
+      Host Controller Location: Built-in USB
+      Host Controller Driver: AppleUSBEHCI
+      PCI Device ID: 0x0aa9 
+      PCI Revision ID: 0x00b1 
+      PCI Vendor ID: 0x10de 
+      Bus Number: 0x26 
+
+        Hub:
+
+          Product ID: 0x2504
+          Vendor ID: 0x0424  (SMSC)
+          Version: 0.01
+          Speed: Up to 480 Mb/sec
+          Location ID: 0x26200000 / 3
+          Current Available (mA): 500
+          Current Required (mA): 2
+
+            USB to ATA/ATAPI Bridge:
+
+              Capacity: 750.16 GB (750,156,374,016 bytes)
+              Removable Media: Yes
+              Detachable Drive: Yes
+              BSD Name: disk1
+              Product ID: 0x2338
+              Vendor ID: 0x152d  (JMicron Technology Corp.)
+              Version: 1.00
+              Serial Number: 313541813001
+              Speed: Up to 480 Mb/sec
+              Manufacturer: JMicron
+              Location ID: 0x26240000 / 5
+              Current Available (mA): 500
+              Current Required (mA): 2
+              Partition Map Type: MBR (Master Boot Record)
+              S.M.A.R.T. status: Not Supported
+              Volumes:
+                Porta-Disk:
+                  Capacity: 750.16 GB (750,156,341,760 bytes)
+                  Available: 668.42 GB (668,424,208,384 bytes)
+                  Writable: Yes
+                  File System: ExFAT
+....
+</pre>
+
+I think its possible to programatically get this information either from the CLI (it dumps out XML output if required) or some development library. There is also DBUS in macports, but I have never had much interaction with it, so I don't know if its good or bad on OSX.
+"""]]